2005 Harley-Davidson Dyna Low Rider - High Explosive

116 Inches Of Dyna-Mite

You could say that this is really the story of three bikes, not just the one in the photos. It began a couple of years back when Carolina Harley-Davidson created an Arlen Ness Y2K scoot for Morri Irvin. He fell in love with the rubber-mount bike, but as often happens with a great motorcycle, someone made him an offer he couldn't refuse. After the check cleared, Morri found himself with a pile of money but no ride.

This brings us to motorcycle number two. Morri again showed up at Carolina H-D in Gastonia, NC, to replace his beloved Y2K. This go-'round, however, he wanted to try a different rubber-mount chassis. After talking it over with Carolina Harley's Jim Bortles, Morri went with a brand-new (at the time) Dyna Low Rider. Plans were made, and the bike went straight into the shop area like a caterpillar into a cocoon.

It emerged eight months later as bike number three (depending on how you count): this orange beauty. Jim put so much work into Morri's ride that it's only barely a Harley and nowhere near a stocker.

That's because Morri wanted something closer to his Y2K than a Dyna. On Jim's recommendation, Irvin gave the go-ahead to cut and reweld the fr ame with the neck at 41 degrees and 6 more inches stretch outward for length; that set the tone for a longer bike. Jim also widened out the back with a new swingarm and 240mm rear tire like the fat rubber on the other ride. New frame work wasn't the only stylistic nod to Morri's old ride, though. More than a few Ness parts were swapped onto this motorcycle, most notably the primary, wheels, back fender, and gas tank.

Insofar as the motor work goes...well, the cases are still Harley. You can't really say that for the rest, though. Part of what Morri loved about his last bike was the combo of a 116-inch motor set in a rubber-mount frame that insulated him from vibration. He absolutely had to have the same feel with this bike. Buddy Cook took care of that by stripping the Twin Cam down to the cases and re-creating it from the bottom up, using JIMS Twin Cam flywheels, rods, pistons, and cylinders to bump up the displacement on a platform that could handle the additional wear and tear. It's topped off by Screamin' Eagle heads and valves as well as JIMS rockers with Pro-One boxes.

Even though Morri and Jim went into the transformation looking to make something along the lines of a Pro-Streeted Harley/Y2K lovechild, as the creation process flowed along, Jim grew more ambitious, and Morri was cool with that. The whole seat area and battery box were hand-fabricated and flow with the lines of the seat and back fender, almost as if the pan were trimmed for the pointed solo butt rest. Moreover, the pointed and curved struts were a great touch that fits the general design to a "T."

It was the crowning touch to this jewel, and, like a jeweler, Jim took the original Dyna and used welder and grinder to bring out the diamond within it. In the end he gave Morri everything he'd loved about his last rubber-mount, plus a whole lot more through the blood and sweat he poured into the fabrication.

SPEC SHEET
GENERAL
OWNER MORRI IRVIN
SHOP CAROLINA HARLEY-DAVIDSON
PHONE (704) 867-2855
WEBSITE WWW.CAROLINAHARLEY.COM
YEAR/MAKE/MODEL '05/H-D/DYNA LOW RIDER
FABRICATION JIM BORTLES AT CAROLINA H-D
ASSEMBLY JIM BORTLES AT CAROLINA H-D
BUILD TIME ONE YEAR
ENGINE
YEAR/TYPE/SIZE '05/H-D/JIMS TWIN CAM/116CI
BUILDER BUDDY COOK AT CAROLINA H-D
CASES H-D
FLYWHEELS JIMS
RODS JIMS
PISTONS JIMS
CYLINDERS JIMS
HEADS SCREAMIN' EAGLE
VALVES SCREAMIN' EAGLE
ROCKERS JIMS
ROCKER BOXES PRO-ONE
PUSHRODS JIMS
PUSHROD TUBES H-D
CAM(S) ANDREWS
LIFTERS JIMS
CARBURETOR S&S; E-SERIES
AIR CLEANER TRIBAL MOTORWORKS
IGNITION DYNATEK
EXHAUST VANCE & HINES
TRANSMISSION
YEAR/TYPE '05/H-D FIVE-SPEED
CASE H-D
GEARS H-D
CLUTCH PRIMO
PRIMARY DRIVE PRIMO
FRAME
YEAR/TYPE '05/H-D DYNA LOW RIDER
RAKE 41 DEGREES
STRETCH 6 INCHES OUT
SUSPENSION
FRONT GOLDAMMER
LENGTH 4 INCHES OVER
TRIPLE-TREES GOLDAMMER CYCLE WORKS
REAR
SWINGARM CENTRAL VALLEY CUSTOMS
SHOCKS B&T;
WHEELS, TIRES, AND BRAKES
FRONT
BUILDER/SIZE ARLEN NESS/16-INCH
TIRE/SIZE METZELER/130
CALIPER(S) PM
ROTOR ARLEN NESS
REAR
BUILDER/SIZE ARLEN NESS/16-INCH
TIRE/SIZE METZELER/{{{240}}}
CALIPER PM
ROTOR ARLEN NESS
FINISH/PAINT
COLOR PEARL CRYSTAL ORANGE
PAINTER CRAZY HORSE PAINTING
GRAPHICS JOANN BORTLES
MOLDING LITTLE ROCK AUTO BODY
ACCESSORIES
FRONT FENDER V-ROD (EXTENDED)
REAR FENDER ARLEN NESS
GAS TANK ARLEN NESS
OIL TANK PYO
GAUGES DAKOTA DIGITAL
HANDLEBARS PYO
MIRRORS ARLEN NESS
HAND CONTROLS PM
FOOT CONTROLS PM
FOOTPEGS PM
HEADLIGHT ACCESSORIES UNLIMITED
TAILLIGHT PYO
TURN SIGNALS NONE
LICENSE MOUNT PYO
SEAT DANNY GRAY