2003 Victory Vegas - First Of Its kind

James Crosby's Custom Victory

The unique design of the Jeff Delisle Springer frontend and the Alloy Art Pan headlight really help with the hot rod look of this bike.

This is the Bonneville Victory sponsored by PM, Alloy Art, and Bassani, that James and Matt built. After running 117 mph on the Salt, James took the bike to the Maxton Mile and joined the 125 Club with a 131 mph pass.

James said the modified 100ci Victory engine puts out 146 hp to the rear wheel. He plans to take the bike back to the Maxton Mile and hopes to hit 175 mph.

James Crosby is certainly no stranger to building things that look great and run fast. His father was a crew chief back in the '60s for Summers Brothers Racing, a job that put him in the pits when Bob Summers piloted the "Goldenrod" with its 2,400 horsepower to a little over 409 mph James was too young at the time to participate, but grew up with a wrench in his hand. His father had his own shop and while the other kids were out playing sports, James was wiling his time tinkering on everything from dune buggies to hotrods to racecars.

Eventually James opened his own shop. After a relatively tumultuous period when he went through a little street racing phase, James closed his shop for a bit and worked for a couple different companies, finally deciding to come back after a little hiatus to follow his dreams and start building bikes and hot rods again. The first bike James ever built was back in 1985, and since then he has worked on a number of projects, including finishing the last bike that Johnny Chop began before he passed.

A few years ago James got together with Matt Waring of MBW Motorcycle Products, which produces an array of aftermarket Victory products, and Lloyd Greer of Lloyd Motorworkz, a performance company with an emphasis on Victory motors, deciding to get together and try their luck on the salt at Bonneville. They did pretty well, hitting upwards of 117 mph with pretty bad salt conditions.

The next winter at the V-Twin show in Cincinnati James and Matt were hanging out at their booth looking at the Bonneville bike and started talking about putting together a hotrod Victory. Matt had always wanted to build one, and James was quick to jump on board. He wanted to build something of a cross between a hot rod, an old bobber, and a pro-street. But more importantly, they wanted to create a full custom Victory not built on a Victory chassis. The premise was to prototype the marketplace and to see if there was a place for this kind of bike.

James started with a 2003 Victory Vegas and got rid of the frame, using a rigid frame from Mike Santoro at Mad Mikes Frames with 38 degrees of rake and 2 1/2 inches of stretch in the backbone. Jeff Delisle at Delisle Custom Products supplied a Springer fronend that is 6 inches over, giving the bike a unique stance, like some crazy bobber-hotrod combo. For wheels and brakes James went with Performance Machine. Of course the bike had to be as minimalist as possible, so they left off anything that wasn't absolutely necessary. Jeff Delisle made the rear fender and James modified it a bit.

James wanted to get more performance out of the engine, so he sent it to Lloyd for a little work, make that a lot of work. Lloyd bumped up the displacement from 92ci to 104ci with one of his hop up kits that included new cams, cylinders, pistons as well as some other goodies. James decided to keep the original tank, but wanted to do a seriously cool modification to it. Upon first glance it looks like just a couple of stacks coming out the top of the tank, which it is, but there's a little more to it. The bike has a downdraft injection system and James wanted to utilize that and make it look like the stacks come straight out the top of the tank, so he cut holes through the entire tank and ran the stacks up. With a beefed up Barnett clutch installed, James changed up the stock clutch cable/bell crank with a modified hydraulic slave cylinder for a lighter and smoother hydraulic clutch setup.

James finished the bike up by sending the tins out to Doug Starbuck at Starside Design for a classy custom red and black paint job. Once the bike was back together, James noticed the 92ci badge on the side of the engine. Being that he didn't have one that read 104ci, he just pulled the 100ci badge off the black race bike and called it close enough. In the end everyone involved was really happy with the results, and they discovered that Victory motorcycles can hang with all the others on the custom scene.

SPEC SHEET
BIKE OWNER Matt and Jen at MBW Motorcycle Products
BUILDER James Crosby Designs
YEAR/MAKE/MODEL 2003/Victory Vegas
FABRICATION James Crosby Designs
ASSEMBLY James Crosby Designs
BUILD TIME 3-months
ENGINE
YEAR/ MANUFACTURER '03/Victory
TYPE/SIZE Freedom/104ci
BUILDER Lloyd at Lloyds Motorworkz
CASES Victory
CYLINDERS Llyods
HEADS Victory
PISTONS MBW/Wiseco
ROCKER BOXES Victory
CAM(S) Llyods EFI Victory
EXHAUST James Crosby Designs
TRANSMISSION
YEAR/MANUFACTURER '03/Victory
CASE Victory
CLUTCH Barnett
PRIMARY DRIVE Victory
FRAME
YEAR/MANUFACTURER '08/Mike Santoro-Mad Mikes Frames
RAKE 38-degrees
STRETCH 2 1/2 inches
SUSPENSION
MANUFACTURER FRONT Delisle Custom Products
LENGTH 6 inches over
TRIPLE TREES Delisle Custom Products
MANUFACTURER REAR None
WHEELS, TIRES, AND BRAKES
MANUFACTURER FRONT/TYPE PM/Casino
SIZE HEIGHT/WIDTH 21x2 1/8
TIRE/SIZE {{{90}}}/90-21
CALIPER PM
ROTOR PM
MANUFACTUERER REAR/TYPE PM/Casino
SIZE-HEIGHT/WIDTH 18x8 1/2
TIRE/SIZE {{{240}}}/50-18
CALIPER PM
ROTOR PM
FINISH/PAINT
COLOR Crimson Red and Black
PAINTER Doug Starbuck-Starside Design
GRAPHICS Doug Starbuck
PLATING/POLISHING Millennium Plating
POWDER COATING Concept Powder
ACCESSORIES
REAR FENDER Delisle-Modified
GAS TANK & CAP Victory-James Crsoby/Matt Hotch cap
OIL TANK in case
HANDLEBARS Delisle
RISERS Delisle
MIRRORS None
HAND CONTROLS PM
FOOT CONTROLS PM
FOOTPEGS PM
HEADLIGHT Alloy Art
TAILLIGHT Alloy Art
LICENSE MOUNT Alloy Art
SEAT Bitchin' Seat Company
ELECTRICAL Todd's Cycle/modified Victory harness