Big Bear Choppers Merc Springer $1,500 This Springer is 18-inches over with a2-degree rake Can be built to your desired length keeping with the 0-degree or 2-degree rake in the trees Download instructions from website to measure your frame to ensure correct trail with the Springer rake and length. Comes in a raw finishFor more information, contact Big Bear Choppers at (909) 878-4340, or visit www.bigbearchoppers.com.
Drag Specialties 613 Series Adjustable Shocks $449.95-$549.95 Fully assembled with an adjustable internal spring for pre-load will lower bike up to 2 inches Improved multi-stage velocity-sensitive internal valving will lower the bike up to with hydraulic anti-bottoming for smoother ride Available in chromeFor more information, contact Drag Specialties at www.dragspecialties.com.
Licks Cycles Super Shorties $229-$269 Designed to lower '79 to '07 stock Sportster seat height to 24 inches Shocks measure 10 inches from eye to eye Direct bolt-on replacement for factory shocks are available in many different color combinations Also available for FLT, FLH, FXR, and V-RodsFor more information, contact Licks Cycles at (413) 663-9050, or visit www.lickscycles.com.
Custom Cycle Control Systems Xtra Length Simplified Air Suspension $1,799 SAS-XL adds 2 inches of travel at the swingarm for a total of 6 inches overall No hoses to run and no fittings to fail Comes with internal compressor, dump valve, and new Remote Filtered Air Breather Made for '99 and earlier and '99 and later Softail modelsFor more information, contact Custom Cycle Control Systems at (866) 439-2129, or visit www.customcyclecontrols.com.
Spyke 63mm Inverted Front End $2,040-$3,151 Features speed-sensitive damping and progressive rate springs Comes with chrome-plated trees, chrome-plated 63.5mm diameter upper tube, and hard chrome 45mm diameter slider tube Legs are machined from billet and then chrome-plated Can handle single or dual disc brakesFor more information, contact Spyke at (562) 803-1700, or visit www.spykeinc.com.
Executive Choppers Harman Girder $1,900-$2,800 Updated version of the original Harman Girder has been re-designed with an adjustable rake plate built into the lower web where the bottom tree bolts to the fork Allows for a 0, 3, or 6-degree rake in the frontend Features 1-3/4-inch 4130 Chromoly front legs, 1-inch 4130 rear legs, and the trees are 1-3/4-inch billet steel designed to fit standard bar risersFor more information, contact Executive Choppers at (916) 780-6508, or visit www.executivechoppers.com.
Glide-Pro Shaft And Bushing System $399.95 Stabilizer shaft with bushings supports the hollow rubber mount that stabilizes the swingarm and the transmission into the frame Shaft is constructed of heat-treated PH 17-4 stainless steel providing high-tensile strength, and shaft is corrosion-resistant Bushings are made from injection-molded polymerFor more information, contact Glide-Pro at (619) 449-6521, or visit www.glide-pro.com.
Flyrite Choppers (FRC) Shorty Springer $495 FRC Springer is 4 inches shorter than most stock applications Developed specifically for 30-degree rake frames with no stretch Measures 17-1/2 inches from neck bottom to rear rocker pivot, and includes a 3/4-inch front axleFor more information, contact Flyrite Choppers at (512) 918-CHOP, or visit www.flyritechoppers.com.
Pro-One Billet FrontEnd Starting at $799 Frontend kits include hard chromed 41mm tubes in popular lengths, black or chromed lower legs, contoured Millennium, Fat, or Thin Raked triple trees, custom flush mount axle, handlebar damper kit, and all necessary hardware Other options include smooth or ball-milled trees and lower legs, Standard, Missile, and Rocket lower leg caps, and triple trees with or without integrated directionals These frontends are set up for single disc applications but dual disc conversion kit is availableFor more information, contact Pro-One at (800) 884-4173, or visit www.pro-one.com.
Greg's Custom Cycles Deepsickness Front End $4,950 Frontend actuates differently than a standard hydraulic fork assembly, using an external air shock and a stabilizer link for added control and performance Fork tree and rockers are constructed from billet aluminum and have a wide stance A wide range of handlebars will fit the stock mounting points, and a variety of colors as well as raw or powdercoated finishes are available with air-style shocks and billet rockersFor more information, contact Greg's Custom Cycles at (726) 2744, or visit www.gregscycles.com.